INNOT catalog

Solid Carbide End Mills

Solid carbide end mills from Ø0.5 to Ø20 mm for steels, stainless steels, cast irons, aluminium, superalloys and hardened steels up to 65 HRC. Flat, torus, ball nose and long-neck mould end mills: choose the geometry or configure your custom end mill.

14products
Family
AllEnd mills for every materialLong-neck end mills for moulds
Material
All materialsPSteelMStainlessKCast ironNAluminiumSSuperalloysHHardened
Filter

Showing all 14 results

Sort:
Show:
4-flute flat end mill – universal
Add to wishlist
Compare

4-flute flat end mill – universal

Available

4-flute carbide end mill for steels, alloy steels and cast irons up to 54 HRC, and up to 65 HRC in the hardened-steel version. Available short or long, with or without reduced neck.

ISO P ISO K ISO H Flat (sharp corner) Ø 1–20 mm
Read more
HHardenedPSteelKCast ironFinishing · Semi-finishing
4-flute torus end mill
Add to wishlist
Compare

4-flute torus end mill

Available

End mill with a corner radius: the radius protects the cutting edge and leaves a fillet on the part. For moulds, pockets and shoulders with radius.

ISO P ISO K ISO H Torus (corner radius) Ø 3–20 mm
Read more
HHardenedPSteelKCast ironSemi-finishing · Roughing
6-flute end mill – square, torus and ball nose
Add to wishlist
Compare

6-flute end mill – square, torus and ball nose

Available

Solid carbide end mill with 6 flutes, square, torus or ball nose, for dynamic roughing and finishing: more flutes engaged for higher feed rates and better surfaces on steels, stainless steels, superalloys and hardened steels.

ISO P ISO M ISO S ISO H Square, torus or ball nose Ø 3–20 mm 6 flutes
Read more
HHardenedPSteelMStainlessSSuperalloysFinishing · Semi-finishing · Roughing
2-flute ball nose end mill
Add to wishlist
Compare

2-flute ball nose end mill

Available

Full-radius end mill (R = D/2) for copy milling and finishing of moulds, free-form surfaces and 3D profiles.

ISO P ISO K ISO H Ball nose (R = D/2) Ø 1–20 mm
Read more
HHardenedPSteelKCast ironFinishing
2- and 3-flute end mill for aluminium
Add to wishlist
Compare

2- and 3-flute end mill for aluminium

Available

Polished end mill with wide flute for aluminium and light alloys: no built-up edge, excellent chip evacuation and a bright finish.

ISO N Flat (sharp corner) Ø 3–20 mm
Read more
NAluminiumFinishing · Roughing
4-flute end mill for superalloys
Add to wishlist
Compare

4-flute end mill for superalloys

Available

End mill with a highly heat-stable coating for heat-resistant superalloys and stainless steels. Flat or torus.

ISO S ISO M Torus (corner radius) Ø 3–20 mm
Read more
MStainlessSSuperalloysSemi-finishing
4- and 5-flute end mill for titanium
Add to wishlist
Compare

4- and 5-flute end mill for titanium

Available

4- or 5-flute end mill with variable pitch for titanium alloys and stainless steels: no vibration and large chip volumes.

ISO S ISO M Torus (corner radius) Ø 6–20 mm
Read more
MStainlessSSuperalloysSemi-finishing · Roughing
HSM end mill for fast roughing
Add to wishlist
Compare

HSM end mill for fast roughing

Available

End mill for high-speed machining (HSM) strategies: light cuts and high feeds on steels, alloy steels and cast irons.

ISO P ISO K Torus (corner radius) Ø 6–12 mm
Read more
PSteelKCast ironRoughing
Roughing end mill with wavy cutting edge
Add to wishlist
Compare

Roughing end mill with wavy cutting edge

Available

Wavy cutting edge that breaks the chip: lower cutting forces and vibration, very high removal rates in roughing.

ISO P ISO K ISO N Flat with wavy cutting edge Ø 6–20 mm
Read more
PSteelNAluminiumKCast ironRoughing
End mill for hardened steels up to 65 HRC
Add to wishlist
Compare

End mill for hardened steels up to 65 HRC

Available

End mill for hardened and mould steels up to 65 HRC: ultra-fine grain carbide, high-silicon coating and reinforced cutting edges. Flat, torus or ball nose.

ISO H ISO P ISO K Up to 65 HRC Ø 1–20 mm
Read more
HHardenedPSteelKCast ironFinishing
2-flute torus end mill with long cylindrical neck
Add to wishlist
Compare

2-flute torus end mill with long cylindrical neck

Available

2-flute torus end mill with relieved cylindrical neck for ribs, deep pockets and mould details: it works where the shank cannot reach, up to 65 HRC.

ISO P ISO M ISO K ISO N ISO H Torus Ø 0.5 – 3 mm Cylindrical neck Up to 65 HRC
Read more
HHardenedPSteelNAluminiumKCast ironMStainlessFinishing · Semi-finishing
2-flute ball nose end mill with long cylindrical neck
Add to wishlist
Compare

2-flute ball nose end mill with long cylindrical neck

Available

Ball nose end mill with relieved cylindrical neck for 3D finishing of ribs, fillets and deep mould cavities, up to 65 HRC.

ISO P ISO M ISO K ISO N ISO H Ball nose Ø 0.5 – 3 mm Cylindrical neck Up to 65 HRC
Read more
HHardenedPSteelNAluminiumKCast ironMStainlessFinishing · Semi-finishing
2-flute torus end mill with reinforced tapered neck
Add to wishlist
Compare

2-flute torus end mill with reinforced tapered neck

Available

Torus end mill with reinforced tapered neck: the neck follows the draft angle of the walls, is more rigid and vibrates less in deep mould machining, up to 65 HRC.

ISO P ISO M ISO K ISO N ISO H Torus Ø 0.5 – 3 mm Tapered neck Up to 65 HRC
Read more
HHardenedPSteelNAluminiumKCast ironMStainlessFinishing · Semi-finishing
2-flute ball nose end mill with reinforced tapered neck
Add to wishlist
Compare

2-flute ball nose end mill with reinforced tapered neck

Available

Ball nose end mill with reinforced tapered neck for copy milling and finishing of deep cavities with drafted walls: more rigidity, less vibration, up to 65 HRC.

ISO P ISO M ISO K ISO N ISO H Ball nose Ø 0.5 – 3 mm Tapered neck Up to 65 HRC
Read more
HHardenedPSteelNAluminiumKCast ironMStainlessFinishing · Semi-finishing
INNOT guide

Solid carbide end mills: square, torus and ball nose

INNOT solid end mills are made of carbide, with 2 to 6 flutes and geometries and coatings dedicated to each material: steel, stainless steel, cast iron, aluminium, titanium, superalloys and hardened steel up to 65 HRC.

How to choose the end mill

  • Square end mill: shoulders, slots and contouring with a sharp corner.
  • Torus end mill: the corner radius protects the edge and lasts longer in roughing and hard steels.
  • Ball nose end mill: copy milling and finishing of moulds and 3D surfaces.
  • Number of flutes: 2 or 3 for aluminium and full slots, 4 as the universal choice, 5 and 6 for finishing and dynamic roughing at high feeds.

For moulds there are end mills with a long cylindrical neck or a reinforced tapered neck, to machine deep without vibration. If you need a special size we build it to drawing: use the custom end mill configurator.

Frequently asked questions

Which coating does my end mill need?

AlTiN and TiSiN for steels, hardened steels and dry machining, AlCrN for stainless steel and superalloys, DLC or an uncoated polished end mill for aluminium and non-ferrous materials. The carbide and coatings guide explains the differences.

Do you make custom end mills?

Yes: diameter, lengths, radius, number of flutes, step and coating. Configure the end mill online and get a quote within 30 minutes.

Choose the familyEnd mills for every materialLong-neck end mills for moulds
Can't find the size or do you use another brand's code?Send us the code or the drawing: we reply with a quote within 30 minutes.
Request a quoteFind the equivalent

Filter products

Categories