Fresa torica 2 taglienti a collo lungo cilindrico INNOT
2-flute torus end mill with long cylindrical neck – INNOT technical drawing

2-flute torus end mill with long cylindrical neck

2-flute torus end mill with relieved cylindrical neck for ribs, deep pockets and mould details: it works where the shank cannot reach, up to 65 HRC.

ISO P

ISO M

ISO K

ISO N

ISO H

Torus

Ø 0.5 – 3 mm

Cylindrical neck

Up to 65 HRC

Request a quote

Technical data sheet PDFCutting data, sizes and grades

Want to try it first? Request a free tester

Prices reserved for companiesLog in to your customer area to see your prices and request new ones in one click.
Sign in
Need technical advice? Talk to INNOT

(+39) 375 786 1361 Call · WhatsApp

Also custom made

Sizes, steps and geometries to drawing

Carbide and coatings

Rod and coating chosen for your material

Technical support

We help you choose geometry and coating

Shipping in 24/48 h

For stock orders throughout Italy

Categories: ,

Description

Technical drawing

2-flute torus end mill with long cylindrical neckDeep ribs and moulds · Ø 0.5 – 3 mmINNOTll1 usable lengthL overall lengthØ DØ d1 neckØ dβrelieved cylindrical neckrhead detailDEEP RIBSthe neck goes where the shank cannotØ 0.5 – 3 mm2 flutescylindrical neckup to 65 HRC

Features

Geometry Torus (corner radius), 2 flutes
Neck Relieved cylindrical, just below the cutting diameter: it enters narrow ribs and cavities where the shank cannot pass.
Diameters Ø 0.5 – 3 mm in tight tolerance; intermediate diameters and above Ø3 custom made
Usable length from 1 to 35 mm (up to 12 times the diameter)
Helix 30°, right-hand cut
Shank Ø 4 or Ø 6 h6 with tapered collar
Materials Mould steels, quenched and tempered and hardened steels up to 65 HRC, stainless steels, cast irons, copper and aluminium
Construction Ultra-fine grain solid carbide, coating chosen for the material (high-silicon coating for hardened steels)

Available sizes

Ø D l cutting Ø d1 neck l1 usable Radii r Ø d shank L overall
Ø 0,5 0,75 0,45 1 – 10 0,05 · 0,1 6 50
Ø 0,6 0,9 0,55 2 – 10 0,05 · 0,1 6 50
Ø 0,8 1,2 0,75 2 – 12 0,05 · 0,1 · 0,2 6 50
Ø 1 1,5 0,95 2 – 20 0,1 · 0,2 4 · 6 50 · 60
Ø 1,2 1,8 1,15 2 – 20 0,2 · 0,3 6 50 · 60
Ø 1,5 2,25 1,45 4 – 25 0,2 · 0,3 4 · 6 50 · 60
Ø 2 3 1,9 4 – 25 0,2 · 0,3 · 0,5 4 · 6 50 · 60
Ø 2,5 3,75 2,4 6 – 25 0,3 · 0,5 · 1 6 60
Ø 3 4,5 2,9 8 – 35 0,3 · 0,5 · 1 6 60 · 78

Dimensions in mm. For each diameter the usable lengths shown are available in 1 – 5 mm steps. Other combinations, special radii and intermediate diameters custom made.

When to choose the cylindrical neck

  • Narrow ribs and slots with vertical walls: the neck, slightly smaller than the cutting diameter, goes all the way down.
  • Rest machining in corners and deep details after a larger cutter.
  • For drafted walls or depths beyond 10 – 12 times the diameter choose the reinforced tapered neck.

Coatings and carbide

All coatings are available on this tool, also in custom versions:

TiNTiCNTiAlNAlTiNAlCrNTiSiNAlTiSiNAlCrSiNCrNZrNTiB2DLCta-CCVD diamondUncoated

Compare coatings and carbide grades →

Need a special length or radius?

Diameter, usable length, radius, neck taper, carbide rod and coating: configure the end mill and receive the quote within 30 minutes.

Configure your end mill

Printable cutting data tableAll the data on this page in an INNOT PDF to keep in the shop.Download PDF