Solid Carbide End Mills

End mills for every material

Flat, torus, ball nose and roughing end mills for steels, stainless steels, cast irons, aluminium, superalloys and hardened steels up to 65 HRC.

10products
Family
AllEnd mills for every materialLong-neck end mills for moulds
Material
All materialsPSteelMStainlessKCast ironNAluminiumSSuperalloysHHardened
Filter

Showing all 10 results

Sort:
Show:
4-flute flat end mill – universal
Add to wishlist
Compare

4-flute flat end mill – universal

Available

4-flute carbide end mill for steels, alloy steels and cast irons up to 54 HRC, and up to 65 HRC in the hardened-steel version. Available short or long, with or without reduced neck.

ISO P ISO K ISO H Flat (sharp corner) Ø 1–20 mm
Read more
HHardenedPSteelKCast ironFinishing · Semi-finishing
4-flute torus end mill
Add to wishlist
Compare

4-flute torus end mill

Available

End mill with a corner radius: the radius protects the cutting edge and leaves a fillet on the part. For moulds, pockets and shoulders with radius.

ISO P ISO K ISO H Torus (corner radius) Ø 3–20 mm
Read more
HHardenedPSteelKCast ironSemi-finishing · Roughing
6-flute end mill – square, torus and ball nose
Add to wishlist
Compare

6-flute end mill – square, torus and ball nose

Available

Solid carbide end mill with 6 flutes, square, torus or ball nose, for dynamic roughing and finishing: more flutes engaged for higher feed rates and better surfaces on steels, stainless steels, superalloys and hardened steels.

ISO P ISO M ISO S ISO H Square, torus or ball nose Ø 3–20 mm 6 flutes
Read more
HHardenedPSteelMStainlessSSuperalloysFinishing · Semi-finishing · Roughing
2-flute ball nose end mill
Add to wishlist
Compare

2-flute ball nose end mill

Available

Full-radius end mill (R = D/2) for copy milling and finishing of moulds, free-form surfaces and 3D profiles.

ISO P ISO K ISO H Ball nose (R = D/2) Ø 1–20 mm
Read more
HHardenedPSteelKCast ironFinishing
2- and 3-flute end mill for aluminium
Add to wishlist
Compare

2- and 3-flute end mill for aluminium

Available

Polished end mill with wide flute for aluminium and light alloys: no built-up edge, excellent chip evacuation and a bright finish.

ISO N Flat (sharp corner) Ø 3–20 mm
Read more
NAluminiumFinishing · Roughing
4-flute end mill for superalloys
Add to wishlist
Compare

4-flute end mill for superalloys

Available

End mill with a highly heat-stable coating for heat-resistant superalloys and stainless steels. Flat or torus.

ISO S ISO M Torus (corner radius) Ø 3–20 mm
Read more
MStainlessSSuperalloysSemi-finishing
4- and 5-flute end mill for titanium
Add to wishlist
Compare

4- and 5-flute end mill for titanium

Available

4- or 5-flute end mill with variable pitch for titanium alloys and stainless steels: no vibration and large chip volumes.

ISO S ISO M Torus (corner radius) Ø 6–20 mm
Read more
MStainlessSSuperalloysSemi-finishing · Roughing
HSM end mill for fast roughing
Add to wishlist
Compare

HSM end mill for fast roughing

Available

End mill for high-speed machining (HSM) strategies: light cuts and high feeds on steels, alloy steels and cast irons.

ISO P ISO K Torus (corner radius) Ø 6–12 mm
Read more
PSteelKCast ironRoughing
Roughing end mill with wavy cutting edge
Add to wishlist
Compare

Roughing end mill with wavy cutting edge

Available

Wavy cutting edge that breaks the chip: lower cutting forces and vibration, very high removal rates in roughing.

ISO P ISO K ISO N Flat with wavy cutting edge Ø 6–20 mm
Read more
PSteelNAluminiumKCast ironRoughing
End mill for hardened steels up to 65 HRC
Add to wishlist
Compare

End mill for hardened steels up to 65 HRC

Available

End mill for hardened and mould steels up to 65 HRC: ultra-fine grain carbide, high-silicon coating and reinforced cutting edges. Flat, torus or ball nose.

ISO H ISO P ISO K Up to 65 HRC Ø 1–20 mm
Read more
HHardenedPSteelKCast ironFinishing
INNOT guide

Carbide end mills for every material

Each material has its end mill: the universal 4-flute square end mill for steels and cast irons, the polished 2 and 3-flute end mill for aluminium, variable-pitch end mills for titanium and superalloys, the end mill for hardened steels up to 65 HRC and the HSM and wavy-edge roughing end mills.

For finishing and copying there are the 4-flute torus, the 2-flute ball nose and the 6-flute square, torus or ball nose end mill for dynamic roughing and finishing.

See alsoLong-neck end mills for moulds
Can't find the size or do you use another brand's code?Send us the code or the drawing: we reply with a quote within 30 minutes.
Request a quoteFind the equivalent

Filter products

Categories