Fresa torica 2 taglienti a collo conico rinforzato INNOT
2-flute torus end mill with reinforced tapered neck – INNOT technical drawing

2-flute torus end mill with reinforced tapered neck

Torus end mill with reinforced tapered neck: the neck follows the draft angle of the walls, is more rigid and vibrates less in deep mould machining, up to 65 HRC.

ISO P

ISO M

ISO K

ISO N

ISO H

Torus

Ø 0.5 – 3 mm

Tapered neck

Up to 65 HRC

Request a quote

Technical data sheet PDFCutting data, sizes and grades

Want to try it first? Request a free tester

Prices reserved for companiesLog in to your customer area to see your prices and request new ones in one click.
Sign in
Need technical advice? Talk to INNOT

(+39) 375 786 1361 Call · WhatsApp

Also custom made

Sizes, steps and geometries to drawing

Carbide and coatings

Rod and coating chosen for your material

Technical support

We help you choose geometry and coating

Shipping in 24/48 h

For stock orders throughout Italy

Categories: ,

Description

Technical drawing

2-flute torus end mill with reinforced tapered neckDrafted walls and great depths · Ø 0.5 – 3 mmINNOTll1 usable lengthL overall lengthØ DØ d1 neckØ dβα neck taper 0.5° – 2°rhead detailDRAFTED WALLSthe tapered neck follows the draft and is more rigidØ 0.5 – 3 mm2 flutestapered neck 0.5° – 2°up to 65 HRC

Features

Geometry Torus (corner radius), 2 flutes
Neck Reinforced tapered: starts just below the cutting diameter and widens with a 0.5° to 2° taper up to the collar. It follows the wall draft and is more rigid than a cylindrical neck.
Diameters Ø 0.5 – 3 mm in tight tolerance; intermediate diameters and above Ø3 custom made
Usable length from 2 to 45 mm (up to 15 times the diameter)
Helix 30°, right-hand cut
Shank Ø 6 h6 with tapered collar
Materials Mould steels, quenched and tempered and hardened steels up to 65 HRC, stainless steels, cast irons, copper and aluminium
Construction Ultra-fine grain solid carbide, coating chosen for the material (high-silicon coating for hardened steels)

Available sizes

Ø D l cutting Ø d1 neck l1 usable Radii r Taper α Ø d shank L overall
Ø 0,5 0,75 0,45 2 – 14 0,05 · 0,1 0,5° · 1° · 1,5° · 2° 6 50
Ø 0,6 0,9 0,55 2 – 15 0,05 · 0,1 0,5° · 1° · 1,5° · 2° 6 50
Ø 0,8 1,2 0,75 4 – 20 0,1 · 0,2 0,5° · 1° · 1,5° · 2° 6 50 · 60
Ø 1 1,5 0,95 8 – 35 0,1 · 0,2 · 0,3 0,5° · 1° · 1,5° · 2° 6 60 · 78
Ø 1,2 1,8 1,15 10 – 40 0,1 · 0,2 · 0,3 0,5° · 1° · 1,5° · 2° 6 60 · 78
Ø 1,5 2,25 1,45 10 – 40 0,1 · 0,2 · 0,3 · 0,5 0,5° · 1° · 1,5° · 2° 6 60 · 78
Ø 2 3 1,9 10 – 45 0,1 · 0,2 · 0,3 · 0,5 0,5° · 1° · 1,5° · 2° 6 60 · 78
Ø 2,5 3,75 2,4 10 – 45 0,2 · 0,3 · 0,5 · 1 0,5° · 1° · 1,5° · 2° 6 60 · 78
Ø 3 4,5 2,9 10 – 45 0,1 · 0,2 · 0,3 · 0,5 · 0,8 · 1 0,5° · 1° · 1,5° · 2° 6 60 · 78

Dimensions in mm. For each diameter the usable lengths shown are available in 1 – 5 mm steps with four neck tapers. Other combinations, special radii and intermediate diameters custom made.

Why a tapered neck

  • Mould walls almost always have a draft: the tapered neck follows it and reaches the bottom without touching the wall.
  • For the same usable length the cross-section grows towards the shank: the tool deflects less, vibrates less and leaves a better finish.
  • Choose the taper closest to the draft of your walls: more taper, more rigidity.

Coatings and carbide

All coatings are available on this tool, also in custom versions:

TiNTiCNTiAlNAlTiNAlCrNTiSiNAlTiSiNAlCrSiNCrNZrNTiB2DLCta-CCVD diamondUncoated

Compare coatings and carbide grades →

Need a special length or radius?

Diameter, usable length, radius, neck taper, carbide rod and coating: configure the end mill and receive the quote within 30 minutes.

Configure your end mill

Printable cutting data tableAll the data on this page in an INNOT PDF to keep in the shop.Download PDF